mbettis Posted January 3, 2013 Share Posted January 3, 2013 I'm running a 50 lb. Little Giant that was buit in 1913. I run it on a daily basis. Before firing it up, I lube that baby with chainsaw bar oil. My clutch is getting greasy and affecting performance. Any recommendations would be appreciated. Thanks, Matt Quote Link to comment Share on other sites More sharing options...
macbruce Posted January 3, 2013 Share Posted January 3, 2013 Does the hammer run on after you let up on the treadle? Quote Link to comment Share on other sites More sharing options...
Bob S Posted January 3, 2013 Share Posted January 3, 2013 I'm running a 50 lb. Little Giant that was buit in 1913. I run it on a daily basis. Before firing it up, I lube that baby with chainsaw bar oil. My clutch is getting greasy and affecting performance. Any recommendations would be appreciated. Thanks, Matt why don't you just put less oil on it? If it's running off it's too much oil. Quote Link to comment Share on other sites More sharing options...
SoCal Dave Posted January 3, 2013 Share Posted January 3, 2013 Matt: Contact Sid at Little Giant. I'm sure he knows the solution. In what way is it affecting the hammers performance? Let us know the outcome and what you did to correct the problem. Good luck. Quote Link to comment Share on other sites More sharing options...
onetreeforge Posted January 4, 2013 Share Posted January 4, 2013 I wouldn't even lube my door hinges with chain bar oil Quote Link to comment Share on other sites More sharing options...
SoCal Dave Posted January 4, 2013 Share Posted January 4, 2013 Chain bar oil is what Sid at Little Giant recommends and uses on LG hammers. Quote Link to comment Share on other sites More sharing options...
peacock Posted January 4, 2013 Share Posted January 4, 2013 Bar and chain oil is fine on the ways, pins and babbit bearings. On the clutch bearing and pittman use gun grease. on the clutch lining surface I use ATF. When the clutch gets gummed up I spray it good with WD40 (it's mostly solvent) to cut the old lube so it will run out then relube with the ATF. If you are getting grease in the clutch you are either over greaseing it or the clutch bearing is worn out and needs repoured. I use a pistol grip grease gun for the clutch bearing go easy and when you feel resistance on the lever stop greasing as the breaing is full anymore will just go past the bearing and get on the frictuon surface. Quote Link to comment Share on other sites More sharing options...
MOblacksmith0530 Posted January 6, 2013 Share Posted January 6, 2013 The best lube for the ways and pit-mans would be "way" oil, it is horrendously expensive so use the bar and chain oil it is similar if not as nice and clean. I use exactly what Peacock says (mostly cause I leaned it from him and Sid) and it works well. What is your clutch material? if it is wood it may have absorbed more of the grease than leather would and may need something like alcohol to clean it. Once it is cleaned you will probably have to lube it a little more often until it builds up a film. If your hammer runs on after you let off the treadle it is another sign that you are using too much grease it is keeping it engaged when it should be releasing. Quote Link to comment Share on other sites More sharing options...
Don Hanson Posted January 6, 2013 Share Posted January 6, 2013 Bar and chain oil is fine on the ways, pins and babbit bearings. On the clutch bearing and pittman use gun grease. on the clutch lining surface I use ATF. When the clutch gets gummed up I spray it good with WD40 (it's mostly solvent) to cut the old lube so it will run out then relube with the ATF. If you are getting grease in the clutch you are either over greaseing it or the clutch bearing is worn out and needs repoured. I use a pistol grip grease gun for the clutch bearing go easy and when you feel resistance on the lever stop greasing as the breaing is full anymore will just go past the bearing and get on the frictuon surface. This is exactly what I do on all my Little giants. Except the ATF, need to try that. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.